Northern Communications NUMERIC PAGERS - BRAVO LX
More than just an answering service!
 The Bravo LX Numeric Pager
TURNING YOUR PAGER ON
Press the green button to turn your pager on. Your pager will alert by either a sound or a vibration, indicating it is on. After displaying the power-up screen, the time of day, the date, and an alert indicator are shown on the standby screen.
TURNING YOUR PAGER OFF
Press the black button until “PAGER OFF?” is displayed. Press the green button to turn your pager off.
NOTE: The pager displays the time and date, but not an alert mode indicator. If the alarm is set, the alarm indicator (bell symbol) remains on the screen when the pager is off.
RECEIVING AND READING MESSAGES
Your Bravo LX pager can receive up to sixteen 20-character messages. When a message is received, the pager alerts for eight seconds.
- Press any button to stop the alert
- Press the green button to display the message
- Press the black square button (on the side of the pager) twice while reading your message to return to the standby screen.
Messages longer than 12 characters display on a second screen, indicated by the arrow symbol. Press the green button to display the second screen. The second screen is displayed automatically after one minute, even if the green button is not pressed.
The last screen of your message displays the message slot number and the time received.
If a message is not read, the pager gives a reminder alert every two minutes and the screen displays the number of unread messages (i.e., 1 Page, 2 Pages) until all messages are read.
If the pager receives more messages than its available memory can hold, the new message replaces the oldest read, unlocked message.
An overflow condition occurs when all message slots are filled with unread messages and a new message is received. Upon receipt of a message, while the pager is in the overflow condition, the oldest unread message is discarded. In this mode, the overflow indicator replaces the default idle display with “OVERFLOW”. Messages must be read and erased to clear the overflow display.
TURNING THE LIGHT ON AND OFF
Press the black square button on the side of the pager to turn the light on. To turn the light off, press that button again. The light turns off automatically two seconds after returning to the standby screen.
CHANGING ALERT MODES
Press the black button. Either “SILENT?” or “AUDIO?” is displayed, depending on the current mode. If “AUDIO?” is displayed, the pager is in “Silent” mode. Press the green button to change to “Audible” mode. The pager chirps. If “SILENT?” is displayed, the pager is in “Audible” mode. Press the green button to change to “Silent” mode. The pager vibrates. For your pager to vibrate when a message is received, it must be in “Silent” mode.
SELECTING AN AUDIBLE ALERT
Press the black button until “SET ALERT?” is displayed. Press the green button. The current alert number is displayed, for example: “ALERT 3”, and the pager gives a sample of the alert tone. Press the black button until the desired alert type is displayed. As each alert number is displayed, the pager gives a sample of the alert tone. Press the green button to select the alert number, set the alert tone to be used, and return to the standby screen. When message are received, your pager gives the selected alert only when in the audible mode (signified by the “speaker” symbol on the screen).
SETTING THE TIME
Press the black button until “SET TIME?” is displayed. Press the green button to set the time. The hour flashes. Press the black button to change the hour. Press the green button to switch to the minutes. The first digit of the minute flashes. Press the black button to change the first minute digit. Press the green button to switch to the second digit. The second digit of the minutes flashes. Press the black button to change the second minute digit. Press the green button to switch to AM/PM. The “A” or “P” flashes. Press the black button to change AM/PM. Press the green button to display the 12/24 hour screen. Press the black button to change the 12/24 hour mode. Press the black square button on the side of the pager twice to return to the standby screen.
SETTING THE ALARM
Press the black button until “SET ALARM?” is displayed. Press the green button to select the alarm on/off sequence. “ON” or “OFF” flashes. Press the black button to turn the alarm on or off. Press the green button to switch to the hours. The hour flashes. Press the black button to change the hour. Press the green button to switch to the minutes. The first digit of the minutes flashes. Press the black button to change the first minute digit. Press the green button to switch to the second digit. The second digit of the minutes flashes. Press the black button to change the second minute digit. Press the green button to switch to AM/PM. The “A” or “P” flashes. Press the black button to change AM/PM. Press the black square button on the side of the pager twice to return to the standby screen.
NOTE: The “AM/PM” steps apply when in the 12 hour mode, as opposed to the 24 hour mode.
The “bell” symbol is displayed when the alarm is turned on. The pager vibrates or gives a 20-second alert and “ALARM” is displayed at the selected time. If set, the alarm activates even when the pager is off. Press any button to stop the alarm alert.
SETTING THE DATE
Press the black button until “SET DATE?” is displayed. Press the green button. The month flashes. Press the black button until the desired month is displayed. Press the green button to switch to the day. The day flashes. Press the black until the desired day is displayed. Press the green button to repeat setting the date, if needed. Press the black square button on the side of the pager twice to return to the standby screen.
SAVING MESSAGES
To save a message, press the black button while reading your message. The prompt “PROTECT?” is displayed. Press the green button to protect the message. The lock symbol indicates that your message is saved. Press the black button while reading the saved message to remove the protection. The prompt “UNPROTECT?” is displayed. Press the green button to remove the protection. The lock symbol is removed from the screen. Saved messages cannot be erased or overwritten by new messages when memory is full. You can save up to eight messages.
ERASING MESSAGES
Press the black button until “ERASE ALL?” is displayed. Press the green button. Your read, unprotected messages are erased. The pager returns to the standby screen. The “ERASE ALL?” prompt is displayed only if there are read messages in memory.
SELECTIVE ERASING OF MESSAGES
Press the black button twice while reading a message and the “DELETE?” prompt is displayed. Press the green button to delete the message and return to the standby screen. Only unprotected messages can be deleted.
BATTERY INFORMATION
Your Bravo LX pager is designed to operate with an AAA-size alkaline battery. If the hinged battery door is detached from the pager, it can easily be snapped back into place.
FEATURES
- Backlight: In low-light conditions, the backlight makes the screen easy to read.
- Duplicate Messages: If the same message is received more than once, “DUPLICATE” is displayed at the beginning of the latest message. This message contains the latest timestamp and prevents a repeated message from taking an extra memory slot.
- Low Battery Indicator: When battery power reaches low levels, “LO CELL” is displayed, prompting you to change the battery. All pager alerts change to two seconds in length.
- Message Erase: Messages can be erased all at once or selectively at your choice to free space in memory.
- Memory Retention: All messages remain in memory, even when the pager is off and while the battery is being replaced.
- Memory Capacity: The Bravo LX pager can store up to sixteen 20-character messages, for a total of 320 characters.
- Message Protect: You can protect up to eight messages stored in the pager memory.
- Overflow: “OVERFLOW” is displayed when more unread messages are received than the available message memory can hold. After you read all of your unread messages, the standby screen is displayed.
- Automatic Alert Reset: The pager alerts automatically stop, even if no buttons are pressed.
- Personal Alarm: This alarm can be set to alert you. The alarm works even when the pager is off.
- Reminder Alarm: The pager chirps or vibrates every two minutes until you read all unread messages.
- Standby Screen: The standby screen displays the time of day/date and the indicators.
- Time of Day and Day/Month: The time of day and the date display whether the pager is on or off.
- Timestamp: The time of day a message is received is displayed on the last screen of each message.
- User Selectable Audible Alerts: A selection of five alert tones gives you a choice of message alerts heard when you are paged in the audible alert mode (signified by the speaker symbol).
CLEANING YOUR BRAVO LX PAGER
To clean the pager housing, use a soft, nonabrasive cloth moistened in a mild soap and water solution. Wipe the surface using a second cloth moistened in clean water. Do not place in water. Do not use alcohol or other cleaning solutions.
To download a manual click here.
To find out more please call us 800-461-3317 or 705-673-6888 and ask to speak to a customer representative. Thank you so much for your interest in NCS pager products!
* Please note: NCS only sells pagers in the Canadian marketplace.
| 
