Contents
Section Chapter
(1)
Introduction
(2)
Features
(3)
Icon Description
3.1 Icon Location
3.2 Icon Explanation
(4)
Function Setting
4.1 To Turn The Pager On
4.2 To Turn The Pager Off
4.3 Alert Mode Setting
4.4 Set Mute(Vibration) Mode
4.5 Date and Time Setting
5.1 Read Message
5.2 To Delete All Messages
5.3 To Delete an Individual Message
5.4 Error Message
5.5 Memory Full
1.
Display: 1 line display
20 digits per message / 12 digits per line
with rollover data
2.
Memory: 16 messages
3.
All of the NP30 numeric pager functions are activated through the use
of one switch, making it the easiest pager to operate.
4.
Displays the number and time of the message received at the end of
the message.
5.
Vibration, tone, or melody alert
6.
Unread message indicator
7.
Delete all/one message
8.
When the capacity of messages is over 16 messages, the screen will
show “full”. The oldest message will be deleted
automatically.
9.
Time display can be set in 12 or 24 hours
10.
7 different alerting tones
11.
Displays error and repeat message automatically
12.
Built-in spare power. When you are changing the battery, or the power
is shut off accidentally, messages will be stored in the memory
to prevent loss of messages within 20 seconds. After 20 seconds, the
message is lost and time must be reset.
  2
|
Battery
safety
1.
One AA alkaline battery is required for operation.
2.
Battery Installation:
Unlock the
battery compartment door by sliding the battery door lock in the opposite
direction of the arrow.
Slide the
battery door open.
Insert one AA
alkaline battery, observing the proper polarity.
Replace the
battery door and lock into place.
3.
Installing the battery will turn the pager on. The pager will enter
a self-test mode by emitting one short beep and vibration and the red LED
lamp will turn on for 4 seconds. The pager will display “NP30” on the
screen.
(3) Icon
Description
3.1
 Location
3.2 Icon
Explanation
1. Available range indication
2. Date
3. Time
4. Unread message
5. Alert mode: A speaker symbol will display when in the alert mode.
6. Next page: The “next page” ICON will display if there is any roll over
data.
(4) Function
Setting
4.1
To turn the pager on:
Insert the battery.
Slide the switch to the “N” position to turn the pager on.
The LCD
will display “NP30” for 2 seconds and a speaker icon to denote the pager is
on and ready to receive messages. The
LED will flash green every 5 seconds to indicate pager readiness. 
4
|
(4) Function
Setting
(Con’t)
Then the
standby mode will show on the screen, for example:
4.2
To turn the
pager off:
Slide the
switch to the “•” position to turn the pager off.
In this position, the pager will have a blank screen.
4.3
Alert Mode
Setting:
Slide the
switch to the ”N” position to set the alert mode.
When in the
alert mode, you will hear a beep for 2 seconds and the
speaker symbol
is displayed.
Set Tone:
Push and hold
the switch until the display shows “SET TONE”
Release the switch, then push the switch
again, this will show “bEEP” and the beep alert will start.
When you push
the button again, the screen will show “MUSIC 1” and the musical alert
starts.
5
|
When entered
into “12 hour” or “24 hour” mode, press the switch again to set the time and
date. Slide the switch to the “M” position to choose the number which you
want to change (the number you choose will be flashing), and press the
switch to enter the number. Toggle between “M” and “N” button to go to next
number.
Slide the
switch to “ • ” position to turn off the pager, or wait for 8 seconds and
the pager will return to the standby mode.
(5)
Message Management
5.1
Read Message:
When a page is
received, press and release the switch to display the message.
Messages that
contain more than 20 digits continue on a second screen. This is indicated
by a continuation “
>
“ icon in the lower right corner of the display. The “Unread” icon will
display on the screen if there is an unread message.
“TONE ONLY” is
displayed when a message is received without numeric data.
The number of
unread messages and time received are indicated on the display.
|
|
(4) Function
Setting
(Con’t)
Continue to
push and release the button and the screen will show “MUSIC 2” through
“MUSIC 6” with each musical alert.
 
When finished
setting the tone, hold the button for 2 seconds (or time out for 8 seconds)
and the pager will return to the standby mode.
4.3
Set Mute
(Vibration) Mode:
Slide the
switch to the ”M” position to set the mute (vibration) mode.
 When
in the mute (vibration) mode, the vibe motor will activate for 2 seconds.
No icon will be noted when in the mute mode.
4.4
Date and Time
Setting:
Slide the
switch to the ”M” position.
 Press
and hold the switch for 2 seconds.
The screen will
display:
Slide the
switch to the “N” position to choose “12 Hour” or “24 Hour” mode.
6
|
5.2
To delete all messages:
At the standby screen, press and hold the switch
until the display shows “ dEL ALL” and release the switch. This will delete
all messages except unread messages.
The display
will return to the standby screen.
5.3
To delete an individual message:
Display the
message to be deleted by pressing the switch for 2 seconds.
Press and hold the switch until the pager displays
“dEL” and then release the switch.
|
