|
POWER ON
Press red button for about six seconds. The
pager turns on, and the sound or vibration alert is generated for 16 seconds.
POWER OFF
Press
= white button until the setup menu appears. Press
t
or u to choose
“POWER OFF”, then press red button to confirm.
READ INCOMING PAGE
Press red button to read an incoming
page. Press
t
or u to scroll
through the messages that have been received by the pager. If there are no
messages in the pager, a display showing “NO MESSAGE” will appear. If there are
messages stored, the screen will show how many “UNREAD” messages, and the number
of “TOTAL” messages stored in the pager.
DELETE ALL MESSAGES
While on the standby screen, press
=
twice. Press
t
or u until “ALL” is
flashing. Press the red button to confirm you want to delete all messages. Any
protected (locked) messages will not be deleted.
DELETE A SINGLE MESSAGE
While reading the message you want to
delete, press the = button. Press the
t
or u button until
“DELETE” is flashing. Press the red button to confirm the deletion.
PROTECT (LOCK) A MESSAGE
You can protect (lock) a message to
prevent accidental deletion. While reading the message you want to protect,
press =.button. Press the
t
or u button until
“LOCK” is flashing. Press the red button to confirm the lock. A small picture
of a lock will show up on the message screen beside the date.
SETTING THE TIME AND DATE
Press the
= key to enter setup menu. Press the
t
or u key until
“TIME” is flashing. Press the red key. Use the
t and
u
keys to scroll through the “A” for AM and “P” for PM. Press the red key to move
to the hour digit. Again, use the
t
and u keys to scroll
through the hours. When you get to the correct hour, press the red key to move
to the minutes digits. Continue on until all digits of the time and date are
set correctly. Press the red key to confirm the settings are correct.
SETTING THE ALARM
Press the
= key to enter the setup menu. Press the
t
or u key until
“ALARM” is flashing. Press the red key. Use the
t and
u
keys to turn the alarm on (picture of an alarm) or off (shows a capital “A”),
then set the time and alarm on or off using the same procedure as when you set
the time. Press the red button to confirm the settings.
SETTING THE AUTOMATIC
POWER ON/OFF
Press the
= key to enter the setup menu. Press the
t
or u key until
“AUTO” is flashing. Press the red key. Press the
t
or u
key to scroll between “ENABLE” and “DISABLE”. Press the red button to set the
“ON” and “OFF” times. When you are done programming these in, press the red
button to confirm these settings.
MELODY SETTINGS
Press the
= key to enter setup menu. Press the
t
or u key until
“MELODY” is flashing. Press the
t
or u keys to scroll
through the different melodies. When you find one you want to use, press the
red button to confirm this setting.
CONTRAST SETTING
You can lighten or darken your screen
for easier reading. Press the
=
button twice. Press the
t
or u key until
“CONTRAST” is flashing. Press the
t
or u key to adjust
contrast. When you have reached the desired contrast, press the red button to
confirm the setting.
ALERT MODE SETTING
You can switch between different types
of alerts: Buzzer (audible alert), Motor (vibration alert), or Mute (no alert).
There is an option for “PUBLIC”, but this is not available in our pager area.
To change the alert mode setting, press the
=
button twice. Press the
t
or u button until
“ALERT” is flashing. Press the red button. Scroll between the different types
of alerts until the one you want is flashing. Press the red button to confirm
the setting.
DISPLAY MEMORY OCCUPANCY
You can check to see how much of the
memory you have used up with stored pages by using this feature. Press the
= button
twice to enter the setup menu. Press the
t
or u button until
“MEMORY” is flashing. Press the red button. The percentage of memory used will
show up in words and a bar graph. If there is no memory left, a display showing
“MEMORY FULL” will show. You will have to delete some of the stored messages to
clear the memory. To exit this screen, press the red button.
BATTERY INFORMATION
When the battery is getting low, your
pager will alert you with a picture of a battery on the screen, and the words
“LOW CELL” on the display. The indication will disappear only when the user
replaces the old battery with a new one. The pager will stop working if the
power is too weak to support the pager’s functions. To change the battery, turn
off the pager. Unlock the battery door and push open. Take out old battery and
replace with a new AAA alkaline battery. Make sure polarity (“-“ and “+”) on
the battery matches the symbols on the pager. Replace battery door and slide
lock back into place. Pager can now be turned back on. **Important – always
use an Alkaline battery for proper pager functioning.
| 
